196CALR Medium Duty Belt Driven Cam Adjusted Live Roller Conveyors

TREAD ROLLERS: 1.9” dia. x 16 ga. steel rollers, model 196S.

PRESSURE ROLLERS: 1.9” dia. x 16 ga. steel, model 196S, cam adjustable.

BELTING: 6” wide black PVC-120 COS.

CENTER DRIVE: Reversible drive with 24” integral belt take-up. For units under 8’-0” overall length, drive components must be stacked. Consult factory for minimum unit elevation.

SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30’.

DRIVE PULLEY: 4” dia. with 1-3/16” dia. shaft or 8” dia. with 1-7/16” dia. shaft, both crowned and fully lagged.

END PULLEY: 4” dia., crowned, with 1-3/16” dia. shaft.

RETURN ROLLERS: 1.9” dia. x 16 ga. steel, model 196S, adjustable.

BED: 7” x 1-1/2” x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7’-0” elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.

BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.

SPEED: 60 FPM, constant.

ELECTRICAL CONTROLS: Optional.

END DRIVE: Mounted underneath conveyor. Minimum possible height is 20” TOR for underneath mounted end drive. Belt take-up required for end drive (if substituting end drive for center drive).

SIDE MOUNTED END DRIVE: Provides overall conveyor height of 10”.

192S TREAD ROLLERS: 1.9” dia. x 12 ga. steel tread rollers, model 192S, available in model 192CALR.

GALVANIZED ROLLERS: Both tread and pressure rollers available in galvanized steel, model 196G. Specify tread only or both tread and pressure rollers.

AUXILIARY TAKE-UP: Provides 24” of belt take-up. Specify location. See Power Accessories.

SPEED: Constant speed 3-120 FPM; DC variable speed; AC inverter variable speed. Other constant or variable speeds available. NOTE: CAPACITY CHANGES WITH SPEED.

BELTING: 6” wide black PVC-150; 12” wide PVC-120.

GUARD RAILS: 1-3/4” x 1” formed channel (model GC), adjusts horizontally to 8” wider than roller and vertically to
6” above roller; formed steel fixed (model FSG in 2”, 4” and 6” heights; fixed channel (model FC); 1-1/2” angle
(model GA1-1/2). See Conveyor Accessories.

CEILING HANGERS: 5/8” dia. threaded rod with hardware to attach rods to conveyor. Provides 6’ clearance between ceiling and TOR (furnished in place of floor supports). See Conveyor Accessories.

FLOOR SUPPORTS: Supports, knee braces, casters and polytier supports available. See Conveyor Accessories.

MOTORS: Available through 3 HP in TEFC, explosion proof, dirty duty, brake motor, 115/230/1, 575/3, etc.

ELECTRICAL CONTROLS: Magnetic starter (one direction or reversible); One direction manual starter; Momentary start/stop push button station; For-ward/reversing /stop push button station. Mounting and pre-wiring for units up to 12’ long.