Just Conveyors
Capabilities and Services
Just Conveyors
Product Line
- Gravity
(non powered) - Belt (Belt over Roller or Slider Pan)
- Accumulation and Sortation
- Line Shaft
- Live Roller (Belt and Chain Driven)
- Miscellaneous Powered
- Plastic Belt (Mattop)
- Plastic Belt (Table Top)
- Flexible and Truck Loading
- Low Profile
- Powered Roller
- Bulk Handling and Portable
- Stainless Steel and Food
- Magnetic
- Vacuum
- Custom
- Curves and Turns
- Inclined and Cleated Belt
- Vertical,
Elevator - Indexing
- OEM
- Automation
Just Conveyors
Mfg. Links
- Package and Unit Handling
Conveyor

- Stainless Steel Conveyor

- Low Profile
Conveyor
- Bulk Handling Conveyor

Web Site Validations:
We Accept Major
Credit Cards, ACH, and Wire Transfers:


SZ796LSZ Medium Duty Smart Zone Line Shaft Zero Pressure Acumulation Conveyors

BEST PRICING! QUICKEST SHIPPING! BEST WARRANTY! UNMATCHED SERVICE!
MEDIUM DUTY SMART ZONE LINE SHAFT ZERO PRESSURE ACCUMULATION CONVEYORS
(SZ796LZ)
1.9" x 16 Ga. Steel Roller
Not available for 24 hour shipments.
SZ796LSZ SMART ZONE® quietly accumulates a wide variety of product sizes and features NO minimum weight limitations. SMART ZONE® eliminates sensor rollers and replaces with photo electric sensors to accumulate products with previously difficult minimal weight restrictions. This zero pressure line shaft driven accumulator is ideal for numerous light to medium duty applications since curves, spurs and other modules may be driven by a single drive.

Conveyor Shown with Optional Supports


SPECIFICATIONS
TREAD ROLLERS: 1.9” dia. x 16 ga. steel, model 196S grooved.
DRIVE BELT: 3/16” dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1” dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type “A”), one end only (type “B” or “C”) or none (type “D”). See ‘line shaft coupling chart’ opposite page,
and specify.
CENTER DRIVE: Located approximately 16-1/2” from end of bed section on 4” RC; 18” on 3” and 6” RC.
SPEED: 60 FPM, constant.
ACCUMULATION: Zone singulation
operation; 2’-0” zone length; zones are pneumatically actuated using photo
electric sensors.
BEARINGS: All bearings are precision, lubricated, ball bearing units with composite housings.
BED: 7” x 1-1/2” x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports.
FRL: Unit is provided with filter, regulator, lubricator with 1/4” ports.
PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.
CAPACITY: See technical section for load capacity rating.
OPTIONAL EQUIPMENT
SIDE MOUNTED DRIVE: Provides overall conveyor height of 10”.
ACCUMULATION ZONES: 18” and 30” long zones available, depending on roller centers.
FLOOR SUPPORTS: Supports, knee braces, casters and polytier supports available. See Conveyor Accessories.
CEILING HANGERS: 5/8” dia. threaded rod with hardware to attach rods to conveyor. Provides 6’ clearance between ceiling and TOR (furnished in place of floor supports). See Conveyor Accessories.
CONVEYOR SPEED: Constant speed
15-120 FPM; DC variable speed; AC inverter variable speed. MINIMUM
operating speed for line shaft conveyor
is 30 FPM.
SLUG RELEASE: Products may be slug released rather than individual product release in normal zone singulation;
accumulation mode will not be disturbed when slug release option utilized.
GALVANIZED ROLLERS: Tread rollers available in galvanized steel, model 196G grooved.
MOTORS: Available through 2 HP in TEFC, explosion proof, dirty duty, 115/230/1, 575/3, etc.
HP@ 60 FPM |
“A” MAX |
1/3, 1/2 |
21” |
3/4, 1 |
22” |
1-1/2, 2 |
23” |
CONVEYOR LENGTH |
5’ |
10’ |
15’ |
20’ |
25’ |
30’ |
40’ |
50’ |
60’ |
70’ |
80’ |
90’ |
100’ |
|
BF |
OAW |
UNIT WEIGHTS (lbs.) with 3” Roller Centers (For other centers, deduct weights below) |
||||||||||||
15” |
18” |
362 |
551 |
740 |
928 |
1117 |
1306 |
1683 |
2061 |
2438 |
2816 |
3193 |
3571 |
3948 |
19” |
21” |
382 |
589 |
796 |
1003 |
1210 |
1417 |
1831 |
2244 |
2658 |
3072 |
3486 |
3900 |
4313 |
21” |
24” |
393 |
612 |
831 |
1049 |
1268 |
1486 |
1923 |
2360 |
2797 |
3234 |
3671 |
4108 |
4545 |
25” |
28” |
405 |
646 |
888 |
1130 |
1372 |
1613 |
2096 |
2580 |
3063 |
3546 |
4029 |
4513 |
4996 |
27” |
30” |
425 |
672 |
925 |
1178 |
1431 |
1684 |
2191 |
2697 |
3203 |
3710 |
4216 |
4722 |
5229 |
33” |
36” |
437 |
724 |
1012 |
1300 |
1588 |
1876 |
2452 |
3027 |
3603 |
4179 |
4755 |
5331 |
5906 |
39” |
42” |
468 |
788 |
1146 |
1504 |
1792 |
2079 |
2724 |
3369 |
4015 |
4660 |
5305 |
5950 |
6595 |
Deduct the following weights (lbs.) for other than 3" centers.
Tread Roller Centers |
15” BF |
19” BF |
21” BF |
25” BF |
27” BF |
33” BF |
39” BF |
|||||||
Per 5’ |
Per 10’ |
Per 5’ |
Per 10’ |
Per 5’ |
Per 10’ |
Per 5’ |
Per 10’ |
Per 5’ |
Per 10’ |
Per 5’ |
Per 10’ |
Per 5’ |
Per 10’ |
|
4” |
-14 |
-28 |
-17 |
-34 |
-19 |
-37 |
-21 |
-42 |
-23 |
-45 |
-27 |
-53 |
-31 |
-62 |
6” |
-18 |
-36 |
-34 |
-68 |
-37 |
-74 |
-42 |
-84 |
-45 |
-90 |
-53 |
-106 |
-62 |
-124 |

Pop-out rollers should be retained in frame if unit is elevated to 7’-0” and above.
Just Conveyors
1513 Shirley Way
Bedford, TX 76022
Phone: (817) 494-3911
Fax: (480) 772-4979
Just Conveyors | Copyright 2009 | Privacy Policy | (817) 494-3911

